Alles anzeigenHi,
I bought this 200 gn bullets, for subsonic loads and the price is quite good, around 30 cents.
I'm looking forward to your load. How much pressure do you have at the mouth?
Did you buy 500 straight away? Give me some for a test series! -)
I like the Lapua bullet, but it costs twice as much:
[attach = '1655', 'none', 'true'] [/ attach]
I hope from the grooves, less frictional resistance and therefore higher precision. Crimprille is also always useful.
I will prepare some loads next week and I'm going to test them the first day the range is open. Don't worry I will post pictures of the groups even they are only at 50m without scope.I'm not looking for a highly accurate load here, it is more intended as indoor suppressed shooting / plinking. I did bought 500, if they work we can make a shared purchase.
Subsonics - Unterschall Ladedaten und Erfahrungen
-
-
Super Bericht von Eule, die bestens auch in diesen Thread passt. Eine Subsonic 7.5x55. Ich bin begeistert! Hier der Bericht:
https://mittelkaliber.ch/k31-kurz-sd-special-edition/
Beim Stopfen vom Leerraum bei geschulterten Hülsen, habe ich allerdings etwas Hemmungen. Mit wenig Watte sollte es allerdings kein Problem sein, wie das Beispiel zeigt. Eine zylindrische Hülse wäre der Idealfall, um eine mögliche Propfenbildung zu verhindern.
-
Ich wollte erst aufmucken wegen dem Leerraum, weil normalerweise ein viel zu grosses Theater darum gemacht wird, aber nur 15-20% Füllung ist schon krass wenig.
-
Yesterday I was testing my 300 blackout subsonic load it worked great, I was checking spped with magnetospeed attached to my suppresor. Here are the results of multiple series, the ES is a little bit large but never supersonic, groups where 1 1/2 moa but I was shooting without scope only with a red dot that filled the target center :
Load details 10,6 gn N120, bullet: spire point 200gn CCI Small rifle.
Series 60 Shots: 5 Min 316 Max 335 Avg 323 S-D 7.1 ES 19 Series Shot Speed 60 1 320 m/s 60 2 325 m/s 60 3 322 m/s 60 4 316 m/s 60 5 335 m/s ---- ---- ---- ---- Series 61 Shots: 5 Min 318 Max 328 Avg 324 S-D 3.7 ES 10 Series Shot Speed 61 1 324 m/s 61 2 324 m/s 61 3 328 m/s 61 4 326 m/s 61 5 318 m/s ---- ---- ---- ---- Series 62 Shots: 5 Min 303 Max 323 Avg 313 S-D 8.1 ES 20 Series Shot Speed 62 1 311 m/s 62 2 309 m/s 62 3 303 m/s 62 4 323 m/s 62 5 320 m/s ---- ---- ---- ---- Series 63 Shots: 5 Min 306 Max 331 Avg 320 S-D 9 ES 25 Series Shot Speed 63 1 306 m/s 63 2 320 m/s 63 3 322 m/s 63 4 322 m/s 63 5 331 m/s ---- ---- ---- ---- Series 64 Shots: 5 Min 311 Max 328 Avg 320 S-D 6.2 ES 17 Series Shot Speed 64 1 328 m/s 64 2 322 m/s 64 3 319 m/s 64 4 311 m/s 64 5 323 m/s -
-
Good Result why you choose 50Meters for the Test?
-
Good Result why you choose 50Meters for the Test?
It was the only distance available with paper targets at my range.
-
Das ist ein grossartige Gruppe. Gratuliere!
-
Hallo Zusammen
Ich möchte auch mit dem Wiederladen von .300 Blackout beginnen Supersonic aber vor allem Subsonic. Da ich bereits 9mm wiederlade habe ich immer noch ein 4Kg Dose RS20 und würde am liebsten dieses auch für Blackout benutzen. Hat jemand dieses Pulver schon für Subsonic Laborierungen genutzt?
Als Geschoss hätte ich RWS .308 200grs KS-Geschoss genommen, da ich RWS-Geschosse vergünstigt über meinen Arbeitgeber kaufen könnte. Leider finde ich aber bei RWS keine Ladedaten zu diesem Geschoss für Subsonic-Laborierungen, auch nicht was COL betrifft. Hat irgendjemand ein paar Tips dazu? -
Hi everyone
I would also like to start reloading .300 Blackout Supersonic but most of all Subsonic. Since I am already reloading 9mm, I still have a 4Kg can RS20 and would prefer to use this for blackout as well. Has anyone used this powder for subsonic loads?
As a bullet, I would have taken RWS .308 200grs KS bullet, because I could buy RWS bullets at a reduced price through my employer. Unfortunately, I can't find any loading data for this bullet for subsonic loads at RWS, not even with regard to COL. Does anyone have any tips on this?Pistol powders are generally too fast for rifles, I have only used them for Reduced loads with some extra filer like cotton inside the case to prevent detonation because of the short amount of powder.
I. will recommend you to use rifle powder like N110 and the right load for a 200 gn bullet. If you are shooting from an AR-15 my recommendation is to stick to mag length - 1mm and start from there playin with the COAL.
-
RS20 entspricht anscheinend dem N340 von Vitahvuori und dem HS-6 von Hodgdon. Könnte schon klappen, obwohl ein langsameres Pulver sicher besser wäre. Ich glaube, jemand im Forum hat Quickload. Vielleicht könnte der es ja mal für dich simulieren. So Handgelenk mal Pi würde ich sagen, etwa 5-6 grains. Aber das soll keine Empfehlung sein, und ich würde das nicht ohne Simulation testen wollen. Und selbst wenn es funktioniert, ist die Frage, ob ein Gasdrucklader dann noch sauber die nächste Patrone laden kann.
Man liest viel, dass es relativ schwierig ist, eine genaue .300 BLK selbst zu laden. Man muss wohl ziemlich experimentieren mit verschiedenen Kugeln und Pulvern.
P.S. Habe gerade gesehen, dass hier schon eine Simulation für RS20 und 200 grain Projektil gepostet wurde: Subsonics - Unterschall Ladedaten und Erfahrungen
-
Hab RS20 und RS24 verschossen, aus dem Repetierer problemlos.Die GRT Modellierungen passen und du kannst die Menge Pulver auf deine Lauflänge optimieren...
...aus dem AR musst du schon aufs RS30 umsteigen, damit du genug Gasdruck hast ,damit es repetiert
Tipp: Verwende Magnum oder 223 Zündhütchen
-
Welche Erfahrung habt ihr bei der Geschwindigkeitsveränderung mit und ohne Schalldämpfer bei .300 BLK Subsonics gemacht?
Hab den akustischen Eindruck, das Subsonics um 300-315 m/s ohne Schalldämpfer gemessen, aus dem Schalldämpfer einen Überschnallknall machen (hab leider keine Messung mit Dämpfer).
Anscheinend ist bei dem Kaliber ein kleiner Geschwindigkeitszuwachs normal, aber soviel?
Was sind eure Erfahrungen?
-
Wie lang ist denn dein Lauf? Wenn er sehr kurz ist, macht die relativ grosse Länge des Schallis natürlich schon was aus. Sind ja nur ca. 10%, kann ich mir gut vorstellen.
-
catalan I guess with MAG length you are talking about .300 win mag? I will not use an AR-15, I will buy the SG553BK conversion kit form SIG for my 550. It has a barrel length of 307mm. But I think your suggestion about the mag length -1mm will also count here.
gromadusi Ja, diese Ladedaten habe ich auch schon gesehen, aber leider steht dort nichts ob ein Repertierer oder Halbautomaten genutzt wird. Aber dann werde ich wohl zum RS30 greifen, dass kann ich auch vergünstigt kaufen.
-
talking about .300 win mag?
nein, .300 AAC Blackout Subsonic
-
talking about .300 win mag?
nein, .300 AAC Blackout Subsonic
Er hat ja folgendes gschrieben:"If you are shooting from an AR-15 my recommendation is to stick to mag length - 1mm and start from there playin with the COAL."
Da wir er dochl wohl von win-mag sprechen? Oder was ist sonst mit "mag length" gemeint?? -
Bin kein Wiederlader, aber bin mir sicher dass damit Magazinlänge gemeint ist. Im Sinne von Platz in der Länge für die Patrone
-
Sie sprechen von 300 BLK. 300 Win Mag ist gemäss Wiki 85mm lang , 223 ist nur 57.4, das passt nicht zusammen Alleine die Hülse der 300 Win Mag ist 67mm. N110 passt auch nicht zu 300 Win Mag, wohl aber zu 300 BLK. Der Hinweis zur Länge des Magazins von Aeon ist korrekt, wenn man das nicht berücksichtigt, passt die Patrone zwar ins Patronenlager, aber die Waffe wird zum Einzellader, da nicht über das Magazin zugeführt werden kann - die Patrone wäre ja zu lang dafür.
Es gibt AR-10, die 300 Win Mag schiessen bzw. dafür angepasst werden können, aber meines Wissens keine AR-15. Auch die SG553 ist meines Wissens nicht dafür ausgelegt, da ja für 300 BLK gedacht und entsprechendem Magazinschacht bzw. Magazinen? -